Gas Turbine Upgrades Selector

LM6000 Hybrid EGT

Vibration System Upgrade

The Bently Nevada 3500 Vibration Monitoring System provides continuous, online vibration monitoring for machinery-protection applications. This is the latest vibration system from Bently Nevada that reduces non-critical trips, including noise-driven and transient vibration shutdowns and nuisance vibration alarms/trips during start-up.

KA26 Fast Start

More flexible and reliable starts.

GT11N2 M Upgrade

Enhanced performance and operational flexibility.

Liquid To Dual Fuel - LM2500

Gives your LM2500 with the capability to run on gas or liquid fuel (with or without water injection for NOx control).

Gas To Dual Fuel - LM6000

Provides your gas turbines with the capability to run either on gas or liquid fuel (with or without water injection for NOx control).

LM6000 Peak Performance

Enable your LM6000PC to achieve up to 5% additional output over current nominal power through peak firing.

Advanced Gas Path

DLN Turndown Enhance Combustion

Increase the operational flexibility of your 7E and 9E Dry Low NOx (DLN) combustion systems.

GT24/GT26 Low Part Load

Improved turndown capability solution.

GT8C XL Turbine Upgrade

Extended C-inspection interval.

LM6000 SAC To DLE Conversion

Reach NOx levels as low was 15ppm on your gas turbine.

Performance Improvement Package

Improve performance and extend the hot gas path component life of your B/E-Class gas turbine units.

Direct Drive Ventilation Fan Upgrades

Upgrade your control systems with RX3i, ehnance systems performance and reliability.

LM2500 SAC to DLE

Reach NOx levels as low was 15ppm on your gas turbine.

Fire Protection Panel Upgrade

Replace an outdated scan fire panel with a new updated fire protection panel.

Primary Frequency Control Upgrade

Primary Frequency Control ("PFC") enables a customized frequency response to maintain grid stability.

Fuel Flexibility Conversions

Enhance your fuel use, reduce fuel costs, and grow new revenue opportunities.

Gas To Dual Fuel - LM2500

Provides your gas turbines with the capability to run either on gas or liquid fuel (with or without water injection for NOx control).

9EMax

Deliver significantly more power and slash operating costs with a new 9E four-stage turbine module—without sacrificing reliability.

S7 Fuel Control Upgrade

The latest fuel core incorporates all current software updates to the LM6000 turbine line.

Fast Start Upgrade

The units will have the unique ability to reach full power (simple cycle) from a cold start within 10 minutes (dependant on the turbine type).

Sump Evacuation System

The Sump Evacuation System restores the necessary differential pressure in the bearing sumps to avoid oil leaks during low power operation, engine load rejects or trips from high power.

Cross Fleet Repowering with Aero

Enhanced performance and operational flexibility.

Controls Upgrade - MicroNet™ Plus

Replace your current Mark VI Fuel controller, chassis and software, using new hardware and software for MicroNet Plus.

Power FlexEfficiency

Unleash the full performance and long-term value of your GE F-class gas turbine assets.

Xtend™ Hot Section Upgrade - DLE

Doubles the hot section life, reducing lifecycle cost and increasing availability. Advanced hot section technology from the LM2500 PLUS G4 utilizes improved materials, coatings & enhanced secondary cooling. The Xtend SAC combustor and fuel nozzle kit is available as an option for gas/dry applications.

Rotor Life Management

Remote VSV Monitoring

Allows remote monitoring of the Variable Stator Vanes (VSV) positions.

Water Injection for NOx Reduction

Significantly lowers exhaust NOx to 25 ppm (gas fuel) or 42 ppm (liquid fuel). Demineralized water is injected into the combustion chamber to regulate the flame temperature.

Combustion Fuel Flexibility

You can accommodate a full range of fuel alternatives with GE’s B/E-class combustion systems.

Rotor-In Major Inspection

Save time, reduce costs, and alleviate safety concerns with GE’s rotor-in major inspection.

GT13E2 MXL2 with Additive Manufactured Performance (AMP)

7EA Enhanced Base Offering

Reduce and manage emissions levels.

Gas Turbine Upgrades Selector

GT24/GT26 Compressor Upgrade

Increase plant capacity by 10% with an advanced compressor upgrade

LM6000 Repower - SAC

GE Power Generation LM6000PB and LM6000PD Gas Turbine models can be converted into the latest LM6000 DLE technology. Increasing the output and reliability of your turbine.

Asset Performance Management

Human Machine Interface (HMI) Upgrade

The Human Machine Interface (HMI) upgrade offers improved operator interface and alarm/event management.

4 Hour Lockout Avoidance

7F Gas Turbine DLN2.6+ Flex Combustion Solutions

Rotor Life Management

Ensure your rotor performs over the long term.

EV-Alpha Burner

State-of-the-art combustion technology.

LM5000 to LM6000 Repower

Repower your LM5000 gas turbine with the LM6000 upgrade.

Automatic Voltage Regulator Upgrade

The EX2100e excitation control is our advanced platform for generator excitation systems.

7F Advanced Compressor

The new 7F gas turbine advanced compressor upgrade solution breaks through new performance barriers.

LM6000PC Uprate

GE Power Generation's LM6000PC uprate for gas turbines enable greater operational flexibility. Using advanced materials and higher firing temperatures from the LM6000PG model.

Power Lifemax

The Power LifeMax portfolio uses data-driven insights to reset the clock on your B-/E-class turbines, recapturing lost performance and lengthening asset life.

GT11DXC Compressor Upgrade

Enhanced power output.

Thrust Balance Valve Removal

The thrust balance valve (TBV) is replaced with an on-engine tube and an in-line plate orifice, which are installed with control system software modifications.

Xtend™ Hot Section Upgrade - SAC

Doubles the hot section life, reducing lifecycle cost and increasing availability. Advanced hot section technology from the LM2500 PLUS G4 utilizes improved materials, coatings & enhanced secondary cooling. The Xtend SAC combustor and fuel nozzle kit is available as an option for gas/dry applications.

GT13E1 MC2 Turbine & Compressor Upgrade

Renewed competitiveness: performance, lifetime, and availability.

KA26 Low Load Operation

Emission-compliant enhanced turndown capability.

Gas Turbine Upgrades

Flange-to-Flange Replacement

Controls Upgrade - Mark VIe

Upgrade your Mark VI Fuel Controller and increase your core fuel control, package sequencing and protection

GT13E2 MXL2 Upgrade

A quantum leap in power output, efficiency, and lifetime.

GT9D1X Performance Improvement Package

Boost plant availability and revenues.

T-Fire Solutions

Rad-Rad Combustor Upgrade

GE Power Generation's Rad-Rad combustor is the latest SAC combustor for the LM6000. The new combustor features redesigned primary and secondary swirlers, extending the life of both the combustor and downstream components.

LMS100PA+ Upgrade

This upgrade will increase airflow function into the gas turbine, resulting in more power and higher efficiency.

GT11NM XL/XP Turbine Upgrade

Enhanced performance and operational flexibility.

6B Repowering Upgrade

Enhanced performance and operational flexibility.

Asymmetric Diffuser - LM2500

Dry Low NOX 2.6 Combustion System

Reduce emissions while increasing outage intervals and providing operational flexibility on your 6F or 7F gas turbine assets.

Advanced Extendor

Reduce component wear and combustion repair costs with Advanced Extendor.

Variable Inlet Guide Vanes, with EFS

Variable Inlet Guide Vanes help direct and control inlet airflow to optimize engine performance.

Liquid To Dual Fuel - LM6000

Provides your LM6000 with the capability to run on gas or liquid fuel (with or without water injection for NOx control).

GT26 High Efficiency

Evaporative Cooler

The evaporative cooling system provides a power output and efficiency increase for sites with high ambient temperatures and low relative humidity.

LM2500 Base to Plus/Plus G4

For enhanced output and efficiency the LM2500 gas turbine can be updated to LM2500+ or LM2500+4G.

SPRINT

SPRINT (SPray INTercooling) increases the output and efficiency of LM6000 gas turbines through cooling - and adding mass to - the compressor air flow.

GT11NMC XL/XP Turbine & Compressor Upgrade

An increase in performance and operational flexibility.

GT13E2 AEV Burner

Improved low load operation for maximum flexibility.

Inlet Air Chilling System

An inlet chilling system (chiller + inlet coils) will cool the compressor intake air, increasing the air density and thus engine output.

7FA CMC Stage 1 Shroud

Reduce gas turbine cooling flow and increase performance.

Anti-Icing Upgrade

Ice formation can lead to restrictions in the inlet system resulting in possible damage to package and turbine equipment.

GT11DM Turbine Upgrade

Optimal performance improvement.

TDI Clutch Upgrade - LM2500

GE Power Generations upgrade to the hydraulic starter clutch improves reliability and availability.

High Flow Online Water Wash Upgrade

Increase the effectiveness of online water washes, thereby minimizing the engine performance degradation caused by compressor fouling.

GT13E2 EV-Alpha Burner

State-of-the-art combustion technology.

F-Class Enhanced Compressor

Extend your outage intervals and flexibility with our Dry Low NOx (DLN) 2.6+ combustion system

GT13DM & GT13DC+ Turbine Upgrade

Boost plant availability and revenue.